User & maintenance manual

Electric winch: user manual and safety

How to connect, use and maintain the Kangaroowinch electric winch safely: wiring, clutch, pulling, and monthly care.

Debon TrailersWinches

At a glance

Pulling capacity (4500 model)
2,040 kg / 4,500 lb
Pulling capacity (4000 model)
1,814 kg / 4,000 lb
Rope left on the drum
At least 5 full coils
Safety distance for bystanders
1.5 times the rope length
Snatch block
Use one above 2/3 of the maximum pulling force
Winding load
Wind the rope under a load of at least 5% of the pulling force
Pulling force by layer
Maximum only on the first layers of rope on the drum; it decreases as layers build up
Safety first
  • Never use the winch to lift loads vertically, to transport people or to secure cargo.
  • Wear protective gloves and never handle the rope with bare hands; do not wear loose clothing or jewellery near the drum.
  • Never stand over or step across a tensioned rope; hang a heavy blanket on the rope to limit whiplash if it breaks.
  • Never hook the rope back onto itself around an anchor point: use a strap or chain and a shackle.
  • Do not exceed the maximum pulling force and avoid jerks. If the motor gets too hot to touch or stalls, stop and let it cool down.
  • Never move the clutch lever while the motor is running or under load.
  • Connect the black wire directly to the battery negative terminal only, never to another earth point on the vehicle.
  • Hold the counter nut with a wrench when tightening the motor terminals, otherwise the internal connections can be damaged.
  • Keep the wires away from moving parts, sharp edges and hot surfaces.
  • When the winch is not in use, switch off the power, the wireless remote control and the control unit to avoid accidental starting. Keep remote controls away from children.
  • Do not clean the winch with a pressure washer.

Before you start

Supplied wires too short
Use wires with a larger cross-section, in proportion to the extra length.
Clutch lever sticks (never under load)
Turn the lever with one hand while briefly pressing IN and OUT on the remote control until the gears engage.
Replacing a steel rope with a synthetic rope
Only use a rope whose strength matches the winch pulling force.
Wired and wireless remote controls
Unplug the wired remote control before using the wireless one; when using the wired remote, switch off the wireless remote and the control unit.

Check before every trip

  • Winch bolted with all supplied bolts, washers and nuts before connecting the wiring
  • Rope in good condition: not frayed, kinked or with broken wires
  • Remote control switched off after each use

Maintenance

WhatWhen
Run the winch (or unwind 15 m with the motor, 5 m more by hand, then rewind with the motor)At least once a month
Check that the winch fastening bolts are tightPeriodically
Clean and tighten the electrical connectionsPeriodically
Clean off mud with a brush and running waterAfter use in mud

Steps

0 / 10 done

  1. Wire the winch

    Connect the long black wire to the battery negative (-) terminal, then the long red wire to the positive (+) terminal. Fit a circuit breaker and a fuse on the red wire.

  2. Secure the vehicle

    Lock the vehicle in place with the handbrake or with wheel chocks.

  3. Choose the anchor point

    Select a suitable anchor point. Wrap it with a strap or chain and join the ends with a shackle.

  4. Unwind the rope by hand

    Move the clutch lever to OUT (disengaged) and pull out the rope you need by hand. Leave at least 5 full coils on the drum.

  5. Hook up

    Attach the rope hook to the shackle, with the hook latch closed and the load in the middle of the hook.

  6. Check the connections

    Check the power wire connections, then plug the remote control into the socket on the relay box.

  7. Prepare the vehicle

    Put the gearbox in neutral, start the engine to keep the battery charged and apply the handbrake. Switch on the winch with the main switch.

  8. Engage the clutch

    Move the clutch lever to IN (engaged) and pull the rope firmly by hand to check the drum is engaged.

  9. Take up the slack

    Wind in the excess rope until the rope, strap and shackle are taut, then check again that everything is correctly attached.

  10. Pull

    Control the winch with the IN and OUT buttons. Stop regularly to check that the rope winds evenly on the drum.