Procedure

Replacing the brake shoes (mechanical drum brakes)

How to remove the brake drum, replace the shoes, springs and expander on a KNOTT mechanical drum brake, then refit the drum and adjust the brake.

Cheval LibertéDebon TrailersAll models

Safety first
  • Raise the trailer and secure it so it cannot fall or roll.
  • Unscrew the bearing nut by hand with a spanner. Never use a pneumatic (impact) wrench.
  • Pull the brake drum off by hand. Do not use a puller.
  • When fitting the shoes, make sure the adjuster wedges do not fall out.

Before you start

160 x 35 brake
Place a washer under the head of the adjusting screw.
Adjusting screw does not turn
Replace the adjusting screw and the adjuster block.
Brake rod slack after adjustment
Tighten the ball nut on the rod and lock it with the counter nut.
Trailers up to 2,700 kg GVW
Brake shoe kit 200 x 50 mm (CZ001091).
Trailers above 2,700 kg GVW
Brake shoe kit 250 x 40 mm (CZ001207).

At a glance

Bearing nut torque
280 Nm
Adjusting screw back-off
About 1/4 turn after the shoes start to rub
Handbrake check
Brakes engage with the lever pulled to the 2nd notch

Tools you need

  • Hammer
  • Spanner
  • Torque wrench
  • Screwdriver
  • Mechanical grease

Steps

0 / 29 done

  1. Raise the trailer

    Loosen the wheel screws, then raise the trailer. Secure it so it cannot fall or roll.

  2. Remove the wheel

    Unscrew the loosened wheel screws and take off the wheel.

  3. Remove the hub cap

    Carefully tap the hub cap off with a hammer.

  4. Unscrew the bearing nut

    Unscrew the bearing nut (8) by hand with a spanner. Do not use a pneumatic wrench.

  5. Remove the drum

    Pull the brake drum off by hand, without a puller.

  6. Remove the hold-down spring

    Press the hold-down spring (1) towards the back plate and unhook it from the shoe (2).

  7. Remove the expander

    Put a screwdriver between the shoe (2) and the expander (3) and lever the expander out.

  8. Disconnect the brake cable

    Unclip the cable sheath from its bracket, pull off the sheath end and remove the cable cover cup. Slide the cable out of its eye.

  9. Unhook the short spring

    Unhook the short spring (4).

  10. Remove the shoes

    Bring the shoes together at the expander end and lift them off.

  11. Check the adjuster

    Press the adjuster block (5) to check that the adjuster wedges work with it.

  12. Check the adjusting screw

    Turn the adjusting screw on the back plate (inner side of the drum). If it does not turn, replace the screw and the adjuster block.

  13. Fit the adjusting screw

    Fit the adjusting screw and adjuster block on the back plate. On a 160 x 35 brake, put a washer under the screw head.

  14. Join the shoes

    Connect the two shoes (2) and (7) with the long spring (6), spring ends facing outwards.

    Parts: Brake shoes, long spring

  15. Position the shoes

    Place the shoes on the adjuster wedges, following the shape of the notches. Make sure the wedges do not fall out.

  16. Fit the short spring

    Connect the shoes with the short spring (4), spring ends towards the back plate.

    Parts: Short spring

  17. Fit the expander

    Position the expander (3) with the cable eye slot on the outer side. Insert one end in shoe (7) and the other in shoe (2), levering with a screwdriver.

    Parts: Expander

  18. Fit the hold-down spring

    Clip the hold-down spring (1) back in place.

  19. Reconnect the brake cable

    Slide the brake cable into its eye and refit the cable cover cup. Clip the sheath into the axle bracket and fit the sheath end onto the cover cup.

  20. Refit the drum

    Fit the brake drum back on.

  21. Grease the thread

    Coat the axle stub thread with mechanical grease.

  22. Fit the new bearing nut

    Screw on the new bearing nut (8) by hand with a spanner. Tighten it to 280 Nm with a torque wrench.

    Parts: Bearing nut

  23. Refit the hub cap

    Drive the bearing nut cap back on.

  24. Tighten the adjusting screw

    Turn the adjusting screw on the back plate until the shoes start to rub and the drum is hard to turn.

  25. Back off a quarter turn

    Loosen the screw by about a quarter of a turn. The drum must turn easily, with the shoes rubbing only lightly.

  26. Check the handbrake

    Pull the handbrake lever to the second notch. The trailer brakes should engage.

  27. Tension the brake rod

    If the brake rod is slack, tighten the ball nut on the rod and lock it with the counter nut.

  28. Refit the wheel

    Put the wheel on the drum and screw in the wheel screws.

  29. Lower and tighten

    Lower the trailer and tighten the wheel screws.

Drawings