Replacing the brake shoes (mechanical drum brakes)
How to remove the brake drum, replace the shoes, springs and expander on a KNOTT mechanical drum brake, then refit the drum and adjust the brake.
![]()
All models
- Raise the trailer and secure it so it cannot fall or roll.
- Unscrew the bearing nut by hand with a spanner. Never use a pneumatic (impact) wrench.
- Pull the brake drum off by hand. Do not use a puller.
- When fitting the shoes, make sure the adjuster wedges do not fall out.
Before you start
- 160 x 35 brake
- Place a washer under the head of the adjusting screw.
- Adjusting screw does not turn
- Replace the adjusting screw and the adjuster block.
- Brake rod slack after adjustment
- Tighten the ball nut on the rod and lock it with the counter nut.
- Trailers up to 2,700 kg GVW
- Brake shoe kit 200 x 50 mm (CZ001091).
- Trailers above 2,700 kg GVW
- Brake shoe kit 250 x 40 mm (CZ001207).
At a glance
- Bearing nut torque
- 280 Nm
- Adjusting screw back-off
- About 1/4 turn after the shoes start to rub
- Handbrake check
- Brakes engage with the lever pulled to the 2nd notch
Tools you need
- Hammer
- Spanner
- Torque wrench
- Screwdriver
- Mechanical grease
Steps
0 / 29 done
Raise the trailer
Loosen the wheel screws, then raise the trailer. Secure it so it cannot fall or roll.
Remove the wheel
Unscrew the loosened wheel screws and take off the wheel.
Remove the hub cap
Carefully tap the hub cap off with a hammer.
Unscrew the bearing nut
Unscrew the bearing nut (8) by hand with a spanner. Do not use a pneumatic wrench.
Remove the drum
Pull the brake drum off by hand, without a puller.
Remove the hold-down spring
Press the hold-down spring (1) towards the back plate and unhook it from the shoe (2).
Remove the expander
Put a screwdriver between the shoe (2) and the expander (3) and lever the expander out.
Disconnect the brake cable
Unclip the cable sheath from its bracket, pull off the sheath end and remove the cable cover cup. Slide the cable out of its eye.
Unhook the short spring
Unhook the short spring (4).
Remove the shoes
Bring the shoes together at the expander end and lift them off.
Check the adjuster
Press the adjuster block (5) to check that the adjuster wedges work with it.
Check the adjusting screw
Turn the adjusting screw on the back plate (inner side of the drum). If it does not turn, replace the screw and the adjuster block.
Fit the adjusting screw
Fit the adjusting screw and adjuster block on the back plate. On a 160 x 35 brake, put a washer under the screw head.
Join the shoes
Connect the two shoes (2) and (7) with the long spring (6), spring ends facing outwards.
Parts: Brake shoes, long spring
Position the shoes
Place the shoes on the adjuster wedges, following the shape of the notches. Make sure the wedges do not fall out.
Fit the short spring
Connect the shoes with the short spring (4), spring ends towards the back plate.
Parts: Short spring
Fit the expander
Position the expander (3) with the cable eye slot on the outer side. Insert one end in shoe (7) and the other in shoe (2), levering with a screwdriver.
Parts: Expander
Fit the hold-down spring
Clip the hold-down spring (1) back in place.
Reconnect the brake cable
Slide the brake cable into its eye and refit the cable cover cup. Clip the sheath into the axle bracket and fit the sheath end onto the cover cup.
Refit the drum
Fit the brake drum back on.
Grease the thread
Coat the axle stub thread with mechanical grease.
Fit the new bearing nut
Screw on the new bearing nut (8) by hand with a spanner. Tighten it to 280 Nm with a torque wrench.
Parts: Bearing nut
Refit the hub cap
Drive the bearing nut cap back on.
Tighten the adjusting screw
Turn the adjusting screw on the back plate until the shoes start to rub and the drum is hard to turn.
Back off a quarter turn
Loosen the screw by about a quarter of a turn. The drum must turn easily, with the shoes rubbing only lightly.
Check the handbrake
Pull the handbrake lever to the second notch. The trailer brakes should engage.
Tension the brake rod
If the brake rod is slack, tighten the ball nut on the rod and lock it with the counter nut.
Refit the wheel
Put the wheel on the drum and screw in the wheel screws.
Lower and tighten
Lower the trailer and tighten the wheel screws.